This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
cluster:194 [2020/04/28 13:19] hmeij07 [SMB] |
cluster:194 [2021/06/07 11:41] hmeij07 [Update 12] |
||
---|---|---|---|
Line 69: | Line 69: | ||
* **SMB/ | * **SMB/ | ||
* all users have shares but not class accounts (hpc101-hpc200) | * all users have shares but not class accounts (hpc101-hpc200) | ||
+ | |||
+ | Not any more. Serious conflict between NFS and SMB ACLs if both protocols enabled on same dataset. So **nobody** has a samba share. If you want to drop& | ||
+ | |||
+ | --- // | ||
< | < | ||
Line 111: | Line 115: | ||
Virtual IP '' | Virtual IP '' | ||
- | An update goes like this and is not an interruption. Check for and apply updates. They are applied to partner | + | Critical |
+ | |||
+ | You can always Disable Failover, to fix power feed of switches 192.168.0.0/16 or 10.10.0.0/ | ||
+ | |||
+ | Check Box to Disable Failover | ||
+ | Go to WebUI > System > Failover > Click the Box > Then Click Save (leave default controller setting as is) | ||
+ | |||
+ | This will allow you to make your network change without failing over. | ||
==== SSH ==== | ==== SSH ==== | ||
Line 152: | Line 164: | ||
zfs userspace | zfs userspace | ||
zfs groupspace tank/ | zfs groupspace tank/ | ||
+ | |||
+ | # uttlerly bizarre in v12 these commands change | ||
+ | |||
+ | root@hpcstore2[~]# | ||
+ | hpcstore2% | ||
+ | hpcstore2% zfs get userused@hmeij07 tank/ | ||
+ | NAME | ||
+ | tank/ | ||
+ | hpcstore2% zfs get userquota@hmeij07 tank/ | ||
+ | NAME | ||
+ | tank/ | ||
+ | hpcstore2% zfs get userspace@hmeij07 tank/ | ||
+ | bad property list: invalid property ' | ||
+ | |||
# hpc100 | # hpc100 | ||
Line 346: | Line 372: | ||
</ | </ | ||
- | ==== Update ==== | + | ==== Update |
- | Change the Train to 11.3, then you will apply the update first in the WebUI to the passive controller. | + | See Update 12 for manual update to v12 with Anthony on 03.09.2021 |
+ | |||
+ | **Change the Train** to 11.3, then you will apply the update first in the WebUI to the passive controller. | ||
After its reboots, you will failover to it by **rebooting** the Active controller (the **current** WebUI). | After its reboots, you will failover to it by **rebooting** the Active controller (the **current** WebUI). | ||
Line 360: | Line 388: | ||
Enable HA, click icon | Enable HA, click icon | ||
+ | **Apply Pending Updates** | ||
+ | Upgrades both controllers. Files are downloaded to the Active Controller and then transferred to the Standby Controller. The upgrade process starts concurrently on both TrueNAS Controllers. | ||
+ | Server responds while HA disabled. | ||
+ | |||
+ | Update takes 15 mins in total. | ||
+ | |||
+ | ** 11.3 U5 ** | ||
+ | |||
+ | * Check for Updates, read release Notes, schedule support ticket if needed (major update) | ||
+ | * Apply Pending update, save configuration, | ||
+ | * active/ | ||
+ | * At 100% stanby reboots, HA disables, file system ok | ||
+ | * Check version on standby, Initiate Fail Over (interrupts file system) | ||
+ | * Login, hyou end up on updated, now active server | ||
+ | * Logout/ | ||
+ | * Wait for HA to be enabled, check version on new standby | ||
==== HDD ==== | ==== HDD ==== | ||
Line 387: | Line 431: | ||
</ | </ | ||
+ | |||
+ | ==== Logs ==== | ||
+ | |||
+ | From support: | ||
+ | |||
+ | That information is logged via syslog for the opposite controller. For example, to find the information I did here, I looked in the syslog output on the controller that was passive at the time these alerts occurred. | ||
+ | |||
+ | You can look that information up yourself by opening an SSH session to the passive controller, navigating to the / | ||
+ | |||
+ | |||
+ | ==== Split Brain ==== | ||
+ | |||
+ | When ending up with an error fail over state try console shutdown first. If that does not work cut power to controllers. | ||
+ | |||
+ | ==== fndebug ==== | ||
+ | |||
+ | * first log into support, then download teamviewer | ||
+ | * https:// | ||
+ | * get.teamviewer.com/ | ||
+ | |||
+ | |||
+ | **Manual debug file creation**, then ftp to ftp.ixsystems.com | ||
+ | |||
+ | < | ||
+ | |||
+ | freenas-debug -A | ||
+ | tar czvf fndebug-wesleyan-20201123.tar.gz / | ||
+ | |||
+ | # next look at bottom of fndebug/ | ||
+ | /dev/da10 HGST: | ||
+ | /dev/da9 HGST: | ||
+ | # these drives have not failed yet but have write errors, offline/ | ||
+ | |||
+ | # next look at output of zpool status -x in fndebug/ | ||
+ | # and the error code | ||
+ | # https:// | ||
+ | |||
+ | NAME STATE READ WRITE CKSUM | ||
+ | tank DEGRADED | ||
+ | ... | ||
+ | raidz2-1 | ||
+ | gptid/ | ||
+ | # look for checksums that have failed like this disk in vdev raidz2-1 | ||
+ | |||
+ | # clean up the spare that resilvered (INUSE status) | ||
+ | # then run a clear on the pool. Then we'll try to get another debug. | ||
+ | |||
+ | zpool detach tank gptid/ | ||
+ | zpool clear tank | ||
+ | |||
+ | # that brought all drives back online and the vdevs show | ||
+ | # then via gui added the available drive back as spare | ||
+ | |||
+ | </ | ||
+ | |||
+ | * Monitor the progress of the resilvering operation: 'zpool status -x' | ||
+ | |||
+ | |||
+ | **Replace a failed drive** | ||
+ | |||
+ | * https:// | ||
+ | * drives mentioned above have not failed yet so we must " | ||
+ | |||
+ | < | ||
+ | |||
+ | 1) Go into the Storage > Pools page. Click the Gear icon next to the pool and press the " | ||
+ | 2) Find da4 and press the three-dot options button next to it, then press " | ||
+ | 3) Go to the System > View Enclosure page, select da4 and press " | ||
+ | 4) Physically swap the drive on the rack with its replacement. | ||
+ | 5) Go back to the Storage > Pool > Status page, bring up the options for the removed drive, | ||
+ | 5a) Select member disk from dropdown, and press " | ||
+ | The replacement drive may or may not have been given the name " | ||
+ | 6) Wait for the drive to finish resilvering before proceeding to replace da3. | ||
+ | 6a) Click spinning icon to view progress. Pool status " | ||
+ | Return the drives in original box, return label provided. | ||
+ | |||
+ | </ | ||
+ | |||
+ | ** Pool Unhealthy but not Degraded status** | ||
+ | |||
+ | No failed disks, no deploy of spare, but pool unhealthy. | ||
+ | |||
+ | < | ||
+ | |||
+ | Mar 21 04:03:57 hpcstore2 (da11: | ||
+ | Mar 21 04:03:57 hpcstore2 (da11: | ||
+ | Mar 21 04:03:57 hpcstore2 (da11: | ||
+ | Mar 21 04:03:57 hpcstore2 (da11: | ||
+ | Mar 21 04:03:57 hpcstore2 (da11: | ||
+ | Mar 21 04:03:57 hpcstore2 (da11: | ||
+ | |||
+ | 1) Storage > Pools. Click gear icon next to the pool and press the " | ||
+ | 2) Find da11 and press the three-dot options button next to it, then press " | ||
+ | 3) System > View Enclosure, find& | ||
+ | 4) Physically swap the drive on the rack with its replacement. | ||
+ | 5) Storage > Pool > Status page, bring up three-dot options for the removed drive, | ||
+ | 5a) Select member disk from drop down, and press " | ||
+ | 6) Wait till resilver finishes. | ||
+ | |||
+ | </ | ||
+ | |||
+ | |||
+ | ==== Update 12 ==== | ||
+ | |||
+ | System > Update > Select (new train 12.0-STABLE) | ||
+ | |||
+ | ** Open a console on both controllers without double ssh sessions, directly to hpcstore1/ | ||
+ | |||
+ | '' | ||
+ | '' | ||
+ | |||
+ | Then download updates on passive, check version '' | ||
+ | |||
+ | '' | ||
+ | |||
+ | '' | ||
+ | |||
+ | ...10%...20%...30%...40%...50%...60%...70%...80%...90%...100% | ||
+ | |||
+ | reboot passive | ||
+ | |||
+ | from active ping passive heartbeat IP, when up | ||
+ | |||
+ | check version passive | ||
+ | |||
+ | check boot env '' | ||
+ | |||
+ | on passive '' | ||
+ | |||
+ | now force fail over via GUI (interruptive for 6o seconds) | ||
+ | |||
+ | Anthony did a reboot on active instead, watch log for personality swap | ||
+ | |||
+ | then update the new passive | ||
+ | |||
+ | '' | ||
+ | |||
+ | '' | ||
+ | |||
+ | then check version, reboot new passive, check version, become new standby | ||
+ | |||
+ | Result: personality switch active vs standby, took 35 mins | ||
+ | |||
+ | In two months: ZFS feature updates pathch, not interruptive, | ||
+ | Upgrade done | ||
+ | --- // | ||
+ | |||
+ | Storage > Pool > " | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||