This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
cluster:88 [2010/08/04 20:16] hmeij |
cluster:88 [2010/08/06 15:27] hmeij |
||
---|---|---|---|
Line 67: | Line 67: | ||
===== Step 2 ===== | ===== Step 2 ===== | ||
- | * Select an installer node, insert Kusu Installer into CD/DVD, and connect via USB ports. | + | * Select an installer node, insert Kusu Installer into CD/DVD, and connect |
- | * Installer node (and the compute nodes we'll create) need eth0 (bottom port) connected | + | * Installer node, and 2-3 compute nodes, must have the purple cable connecting |
- | * Boot, hit F2 to Enter BIOS, traverse to menu tab Boot and make sure both CDROM and Removable Device are listed before any other options like hard disk and network cards, hit F10 save changes and exit. | + | * Boot installer node, hit F2 to Enter BIOS, traverse to menu tab Boot and make sure both CDROM and Removable Device are listed before any other options like hard disk and network cards, hit F10, save changes and exit/reboot. |
- | * Next you should see the Project Kusu splash page with the orange turtle; when prompted type ' | + | * Next you should see the Project Kusu splash page with the orange |
- | * Navigation | + | * Navigation |
* Next come the informational screens, in order | * Next come the informational screens, in order | ||
- | | + | * 1 - language: English |
- | - keyboard: us | + | * 2 - keyboard: us |
- | - network, configure each interface, edit and configure two private networks (for Pace we'll reset eth1 on installer node later on for public access), this is so that the cluster is not accessible from outside and we could separate provision from private (NFS data/MPI) traffic. | + | * 3 - network, configure each interface, edit and configure two private networks (for Pace we'll reset eth1 on installer node later on for public access), this is so that the cluster is not accessible from outside and we could separate provision from private (NFS data/MPI) traffic. |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | - gateway & dns: gateway 192.168.101.0 (is not used but required field), dns server 192.168.101.254 (installer node) | + | * 4 - gateway & dns: gateway 192.168.101.0 (is not used but required field), dns server 192.168.101.254 (installer node) |
- | - host: FQDN kusu101, PCD kusu101 (basically we will not provide internet accessible names) | + | * 5 - host: FQDN kusu101, PCD kusu101 (basically we will not provide internet accessible names) |
- | - time: American/ | + | * 6 - time: American/ |
- | - root password: password (keep simple for now, change later) | + | * 7 - root password: password (keep simple for now, change later) |
- | - partition: select 'Use Default' | + | * 8 - disk partitions: select 'Use Default' |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | - confirm: accept (at this point the disk gets reformatted) | + | * 9 - confirm: accept (at this point the disk gets reformatted) |
- | - kits: select Add, cycle through disks by kit, then Finish (node reboots). | + | * 10 - kits: select Add, insert kit cd, wait, cycle through disks by kit, then No More Kits, then Finish (node reboots). |
\\ | \\ | ||
**[[cluster: | **[[cluster: |