cluster:228
IB BIOS settings
- applies to nodes n102-n107
- NFSoRDMA, see NFSoRDMA
- from support at Microway
- then fix NFS mount on n103
Here are the BIOS setting we set for those system prior to shipping;
Start by entering the BIOS and taking the "Optimized Defaults" (F3)
Then going down through the menus on the "Advanced" tab in the
BIOS...
Boot Feature;
Quiet Boot = disabled
Wait for "F1" if Error = disabled
CPU Configuration:
Extended APIC = enabled
"Advanced Power Management Configuration"
Power technology = Custom
Power Performance Tuning= BIOS controls EPB
ENERGY_PERF_BIAS_CFG Mode = Max Performance
PCIe/PCI/Pnp Configuration
Above 4Gb Decoding = enabled
Then arrow right over to the "Boot" tab at the top
Boot Mode Select = UEFI
Then you set the "Fixed Boot Order Priorities"
Typically we set them like this but the choices may vary depending
on boot mode and what you have installed for components.
USB Floppy
USB CD/DVD
USB Hard Disk
USB LAN
USB Key
UEFI CD/DVD
UEFI Hard Disk
UEFI Network
Some of the boot order options that I have above like "UEFI
Network" might have a slightly different name but it's the idea of
external devices like USB, then local like a CD/DVD drive, then a hard
drive to boot off of and then the network last.
Once you have the changes made...hit "F4" to save the changes and
the system will reboot.
Check to make sure your IB card is showing then.
I think the "Extended APIC" option being enabled allows your IB card to show.
The CPUs control the PCIe lanes so that options allows more "space" for the PCI lanes.
MFT fix
We got a new raid card. ib0 device not available
After stepping through all memory configs from 2 dimms to 16 dimms
Then we added the card.
The card shows up but is still down/disabled.
# modules loaded
[root@n103 ~]# lsmod | grep mlx5
mlx5_ib 397312 0 <---
ib_uverbs 163840 2 rdma_ucm,mlx5_ib
ib_core 397312 12 rdma_cm,ib_ipoib,rpcrdma,ib_srpt,iw_cm,ib_iser,ib_umad,ib_isert,rdma_ucm,ib_uverbs,mlx5_ib,ib_cm
mlx5_core 1703936 1 mlx5_ib <----
mlxfw 32768 1 mlx5_core
pci_hyperv_intf 16384 1 mlx5_core
tls 110592 1 mlx5_core
psample 20480 1 mlx5_core
# cable and power
[root@n103 ~]# dmesg | grep -i mlx5
[ 3.097033] mlx5_core 0000:31:00.0: firmware version: 16.34.1002
[ 3.097071] mlx5_core 0000:31:00.0: 126.016 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x16 link) <----
[ 3.505586] mlx5_core 0000:31:00.0: Rate limit: 127 rates are supported, range: 0Mbps to 97656Mbps
[ 3.505893] mlx5_core 0000:31:00.0: E-Switch: Total vports 2, per vport: max uc(128) max mc(2048)
[ 3.510968] mlx5_core 0000:31:00.0: Port module event: module 0, Cable plugged <----
[ 3.511247] mlx5_core 0000:31:00.0: mlx5_pcie_event:300:(pid 818): PCIe slot advertised sufficient power (75W). <----
[ 3.550721] mlx5_core 0000:31:00.0: MLX5E: StrdRq(1) RqSz(8) StrdSz(2048) RxCqeCmprss(0)
[ 3.788710] mlx5_core 0000:31:00.0: Supported tc offload range - chains: 4294967294, prios: 4294967295
[ 16.530223] mlx5_core 0000:31:00.0 eth2: Link down
# in order to enable infiniband read on and find solution...
# download mft, stored on astrostore:/usr/local/src
https://network.nvidia.com/products/adapter-software/firmware-tools/
# copy from n102:/usr/local/src the mft-4.23-rpms
# collected from a previous installation
cd mft-4.23-rpms/
[root@n103 mft-4.23-rpms]# ls
annobin-10.67-3.el8.x86_64.rpm make-4.2.1-11.el8.x86_64.rpm
dwz-0.12-10.el8.x86_64.rpm ocaml-srpm-macros-5-4.el8.noarch.rpm
efi-srpm-macros-3-3.el8.noarch.rpm openblas-srpm-macros-2-2.el8.noarch.rpm
elfutils-0.187-4.el8.x86_64.rpm patch-2.7.6-11.el8.x86_64.rpm
elfutils-libelf-devel-0.187-4.el8.x86_64.rpm perl-srpm-macros-1-25.el8.noarch.rpm
gc-7.6.4-3.el8.x86_64.rpm python3-rpm-generators-5-7.el8.noarch.rpm
gcc-plugin-annobin-8.5.0-16.el8_7.x86_64.rpm python3-rpm-macros-3-43.el8.noarch.rpm
gdb-headless-8.2-19.el8.x86_64.rpm python-rpm-macros-3-43.el8.noarch.rpm
ghc-srpm-macros-1.4.2-7.el8.noarch.rpm python-srpm-macros-3-43.el8.noarch.rpm
go-srpm-macros-2-17.el8.noarch.rpm qt5-srpm-macros-5.15.3-1.el8.noarch.rpm
guile-2.0.14-7.el8.x86_64.rpm redhat-rpm-config-130-1.el8.noarch.rpm
kernel-devel-4.18.0-425.3.1.el8.x86_64.rpm rpm-build-4.14.3-24.el8_7.x86_64.rpm
libatomic_ops-7.6.2-3.el8.x86_64.rpm rust-srpm-macros-5-2.el8.noarch.rpm
libbabeltrace-1.5.4-4.el8.x86_64.rpm zlib-devel-1.2.11-21.el8_7.x86_64.rpm
libipt-1.6.1-8.el8.x86_64.rpm zstd-1.4.4-1.el8.x86_64.rpm
# you need these rpms
rpm -iv rpm-build-4.14.3-24.el8_7.x86_64.rpm elfutils-0.187-4.el8.x86_64.rpm \
zstd-1.4.4-1.el8.x86_64.rpm python3-rpm-generators-5-7.el8.noarch.rpm
# and
rpm -ivh rpm-build kernel-devel # for running kernel version
# gunzip, untar mft tarball
cd /usr/local/src/tmp
cd mft-4.23.0-104-x86_64-rpm/
./install.sh
-I- Removing any old MFT file if exists...
-I- Building the MFT kernel binary RPM...
-I- Installing the MFT RPMs...
Verifying... ################################# [100%]
Preparing... ################################# [100%]
Updating / installing...
1:kernel-mft-4.23.0-4.18.0_425.3.1.################################# [100%]
Verifying... ################################# [100%]
Preparing... ################################# [100%]
Updating / installing...
1:mft-4.23.0-104 ################################# [100%]
-I- In order to start mst, please run "mst start".
mst start
Starting MST (Mellanox Software Tools) driver set
Loading MST PCI module - Success
Loading MST PCI configuration module - Success
Create devices
Unloading MST PCI module (unused) - Success
# you will need
git clone https://github.com/stanford-rc/ibswinfo.git
cd ibswinfo/
scp -p ibswinfo.sh /usr/bin/
cd /usr/bin
ln -s ibswinfo.sh ibswinfo
[root@n103 src]# ibstat
CA 'mlx5_0'
CA type: MT4119
Number of ports: 1
Firmware version: 16.34.1002
Hardware version: 0
Node GUID: 0x98039b03007045f2
System image GUID: 0x98039b03007045f2
Port 1:
State: Down
Physical state: Disabled
Rate: 40
Base lid: 0
LMC: 0
SM lid: 0
Capability mask: 0x00010000
Port GUID: 0x9a039bfffe7045f2
Link layer: Ethernet <--- this needs to change
# read this post, all the way to the bottom
https://forums.developer.nvidia.com/t/mlx5-0-mlx5-1-down/316392
# useful articles
https://docs.nvidia.com/networking/display/mftv422/using+mlxconfig
https://docs.nvidia.com/networking/display/mftv4180/compilation+and+installation
rpm -qf /usr/bin/mlxconfig
mft-4.23.0-104.x86_64
# now configure port on new Mellanox card, first a query
mlxconfig -d /dev/mst/mt4119_pciconf0 q
Device #1:
----------
Device type: ConnectX5
Name: MCX555A-ECA_Ax_Bx
Description: ConnectX-5 VPI adapter card; EDR IB (100Gb/s) and 100GbE; single-port QSFP28; PCIe3.0 x16; tall bracket; ROHS R6
Device: /dev/mst/mt4119_pciconf0
Configurations: Next Boot
MEMIC_BAR_SIZE 0
MEMIC_SIZE_LIMIT _256KB(1)
HOST_CHAINING_MODE DISABLED(0)
HOST_CHAINING_CACHE_DISABLE False(0)
HOST_CHAINING_DESCRIPTORS Array[0..7]
HOST_CHAINING_TOTAL_BUFFER_SIZE Array[0..7]
FLEX_PARSER_PROFILE_ENABLE 0
FLEX_IPV4_OVER_VXLAN_PORT 0
ROCE_NEXT_PROTOCOL 254
ESWITCH_HAIRPIN_DESCRIPTORS Array[0..7]
ESWITCH_HAIRPIN_TOT_BUFFER_SIZE Array[0..7]
PF_BAR2_SIZE 0
PF_NUM_OF_VF_VALID False(0)
NON_PREFETCHABLE_PF_BAR False(0)
VF_VPD_ENABLE False(0)
PF_NUM_PF_MSIX_VALID False(0)
PER_PF_NUM_SF False(0)
STRICT_VF_MSIX_NUM False(0)
VF_NODNIC_ENABLE False(0)
NUM_PF_MSIX_VALID True(1)
NUM_OF_VFS 0
NUM_OF_PF 1
PF_BAR2_ENABLE False(0)
SRIOV_EN False(0)
PF_LOG_BAR_SIZE 5
VF_LOG_BAR_SIZE 1
NUM_PF_MSIX 63
NUM_VF_MSIX 19
INT_LOG_MAX_PAYLOAD_SIZE AUTOMATIC(0)
PCIE_CREDIT_TOKEN_TIMEOUT 0
ACCURATE_TX_SCHEDULER False(0)
PARTIAL_RESET_EN False(0)
SW_RECOVERY_ON_ERRORS False(0)
RESET_WITH_HOST_ON_ERRORS False(0)
ADVANCED_POWER_SETTINGS False(0)
CQE_COMPRESSION BALANCED(0)
IP_OVER_VXLAN_EN False(0)
MKEY_BY_NAME False(0)
ESWITCH_IPV4_TTL_MODIFY_ENABLE False(0)
PRIO_TAG_REQUIRED_EN False(0)
UCTX_EN True(1)
PCI_ATOMIC_MODE PCI_ATOMIC_DISABLED_EXT_ATOMIC_ENABLED(0)
TUNNEL_ECN_COPY_DISABLE False(0)
LRO_LOG_TIMEOUT0 6
LRO_LOG_TIMEOUT1 7
LRO_LOG_TIMEOUT2 8
LRO_LOG_TIMEOUT3 13
LOG_TX_PSN_WINDOW 7
LOG_MAX_OUTSTANDING_WQE 7
ROCE_ADAPTIVE_ROUTING_EN False(0)
TUNNEL_IP_PROTO_ENTROPY_DISABLE False(0)
ICM_CACHE_MODE DEVICE_DEFAULT(0)
TX_SCHEDULER_BURST 0
ZERO_TOUCH_TUNING_ENABLE False(0)
LOG_MAX_QUEUE 17
LOG_DCR_HASH_TABLE_SIZE 11
MAX_PACKET_LIFETIME 0
DCR_LIFO_SIZE 16384
LINK_TYPE_P1 ETH(2)
ROCE_CC_PRIO_MASK_P1 255
CLAMP_TGT_RATE_AFTER_TIME_INC_P1 True(1)
CLAMP_TGT_RATE_P1 False(0)
RPG_TIME_RESET_P1 300
RPG_BYTE_RESET_P1 32767
RPG_THRESHOLD_P1 1
RPG_MAX_RATE_P1 0
RPG_AI_RATE_P1 5
RPG_HAI_RATE_P1 50
RPG_GD_P1 11
RPG_MIN_DEC_FAC_P1 50
RPG_MIN_RATE_P1 1
RATE_TO_SET_ON_FIRST_CNP_P1 0
DCE_TCP_G_P1 1019
DCE_TCP_RTT_P1 1
RATE_REDUCE_MONITOR_PERIOD_P1 4
INITIAL_ALPHA_VALUE_P1 1023
MIN_TIME_BETWEEN_CNPS_P1 4
CNP_802P_PRIO_P1 6
CNP_DSCP_P1 48
LLDP_NB_DCBX_P1 False(0)
LLDP_NB_RX_MODE_P1 OFF(0)
LLDP_NB_TX_MODE_P1 OFF(0)
DCBX_IEEE_P1 True(1)
DCBX_CEE_P1 True(1)
DCBX_WILLING_P1 True(1)
KEEP_ETH_LINK_UP_P1 True(1)
KEEP_IB_LINK_UP_P1 False(0)
KEEP_LINK_UP_ON_BOOT_P1 False(0)
KEEP_LINK_UP_ON_STANDBY_P1 False(0)
DO_NOT_CLEAR_PORT_STATS_P1 False(0)
AUTO_POWER_SAVE_LINK_DOWN_P1 False(0)
NUM_OF_VL_P1 _4_VLs(3)
NUM_OF_TC_P1 _8_TCs(0)
NUM_OF_PFC_P1 8
VL15_BUFFER_SIZE_P1 0
DUP_MAC_ACTION_P1 LAST_CFG(0)
MPFS_MC_LOOPBACK_DISABLE_P1 False(0)
MPFS_UC_LOOPBACK_DISABLE_P1 False(0)
UNKNOWN_UPLINK_MAC_FLOOD_P1 False(0)
SRIOV_IB_ROUTING_MODE_P1 LID(1)
IB_ROUTING_MODE_P1 LID(1)
PHY_AUTO_NEG_P1 DEVICE_DEFAULT(0)
PHY_RATE_MASK_OVERRIDE_P1 False(0)
PHY_FEC_OVERRIDE_P1 DEVICE_DEFAULT(0)
PF_TOTAL_SF 0
PF_SF_BAR_SIZE 0
PF_NUM_PF_MSIX 63
ROCE_CONTROL ROCE_ENABLE(2)
PCI_WR_ORDERING per_mkey(0)
MULTI_PORT_VHCA_EN False(0)
PORT_OWNER True(1)
ALLOW_RD_COUNTERS True(1)
RENEG_ON_CHANGE True(1)
TRACER_ENABLE True(1)
IP_VER IPv4(0)
BOOT_UNDI_NETWORK_WAIT 0
UEFI_HII_EN True(1)
BOOT_DBG_LOG False(0)
UEFI_LOGS DISABLED(0)
BOOT_VLAN 1
LEGACY_BOOT_PROTOCOL PXE(1)
BOOT_RETRY_CNT NONE(0)
BOOT_INTERRUPT_DIS False(0)
BOOT_LACP_DIS True(1)
BOOT_VLAN_EN False(0)
BOOT_PKEY 0
P2P_ORDERING_MODE DEVICE_DEFAULT(0)
ATS_ENABLED False(0)
DYNAMIC_VF_MSIX_TABLE False(0)
EXP_ROM_UEFI_x86_ENABLE False(0)
EXP_ROM_PXE_ENABLE True(1)
IBM_TUNNELED_ATOMIC_EN False(0)
IBM_AS_NOTIFY_EN False(0)
ADVANCED_PCI_SETTINGS False(0)
SAFE_MODE_THRESHOLD 10
SAFE_MODE_ENABLE True(1)
# switch to port from ethernet to infiniband
mlxconfig -d /dev/mst/mt4119_pciconf0 set LINK_TYPE_P1=1
Device #1:
----------
Device type: ConnectX5
Name: MCX555A-ECA_Ax_Bx
Description: ConnectX-5 VPI adapter card; EDR IB (100Gb/s) and 100GbE; single-port QSFP28; PCIe3.0 x16; tall bracket; ROHS R6
Device: /dev/mst/mt4119_pciconf0
Configurations: Next Boot New
LINK_TYPE_P1 ETH(2) IB(1)
Apply new Configuration? (y/n) [n] : y
Applying... Done!
-I- Please reboot machine to load new configurations.
reboot
[root@n103 ~]# ibstat
CA 'mlx5_0'
CA type: MT4119
Number of ports: 1
Firmware version: 16.34.1002
Hardware version: 0
Node GUID: 0x98039b03007045f2
System image GUID: 0x98039b03007045f2
Port 1:
State: Active
Physical state: LinkUp
Rate: 100
Base lid: 9
LMC: 0
SM lid: 1
Capability mask: 0xa659e848
Port GUID: 0x98039b03007045f2
Link layer: InfiniBand <----- yea
ib0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 2044
inet 10.11.103.103 netmask 255.255.0.0 broadcast 0.0.0.0
Infiniband hardware address can be incorrect! Please read BUGS section in ifconfig(8).
infiniband 00:00:00:43:FE:80:00:00:00:00:00:00:00:00:00:00:00:00:00:00 txqueuelen 256 (InfiniBand)
RX packets 210 bytes 27332 (26.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 228 bytes 17944 (17.5 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
# mount the NFSoRDMA file system
10.11.103.243:/lvm_data /astrostore nfs defaults,proto=rdma,port=20049 0 0
# reload this module in /etc/rc.local before ip map to ib0
/usr/sbin/modprobe -r mlx5_ib
/usr/sbin/modprobe mlx5_ib
sleep 10
/usr/sbin/ip addr add 10.11.103.103/16 dev ib0
cluster/228.txt · Last modified: 2025/02/19 20:47 by hmeij07
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
